1. How to check whether the monitor fits the stand?

1. Check if the monitor size and weight are within the range of monitor stand limitation.
2. Check if there is a 75x75mm/100x100mm VESA hole pattern at the back of your monitor, if there is no hole pattern, you need an additional adapter (HNMUA4) on Amazon.

 

 

2. What to do if the VESA hole pattern on the monitor is too big?

You need a VESA extension adapter (HNMUA4).

 

 

 

3. Can the monitor stand be used on a particle board desk?

Yes, particle board is relatively soft, we suggest our reinforcement plate (HNDA1) and install between the desktop and the mounts base.

 

 

4. Can the monitor stand be used on a glass desk top?

Yes, in order to protect the glass and to add strength to it, we recommended our reinforcement plate (HNDA1) and install it between the desktop and the mounts base.

 

 

5. What should I do if there is a crossbar under the table?

1. It is recommended to place a wooden block of the same size and thickness as the crossbar under the table.
2. Or you can use grommets to mount the stand directly.

 

 

6. How to increase the height of the monitor stand if it is too low?

If the table is too thin, it is recommended to place a wooden block on top of the table, which can add a few inches of height.

 

 

7. What should I do if the VESA head is not straight?

The VESA head can be rotated 360°. Please install the monitor first, and then adjust the monitor to a positive angle. Please note that the head cannot be rotated directly by hand.

 

 

8. The VESA pattern on the back of my monitor is recessed, how do i install the VESA adapter?

The installation can be done with spacers and long screws M4x30mm. Please install the spacer inside/outside the recessed area first, then install the VESA plate and install the screws through the assembly.

 

 

9. What if I can't find the tension adjustment screw to adjust the tension?

The stand must be installed on your desktop. The monitor must then be installed on the stand. Apply pressure to the arm until you see the position of the screw hole. At the two arms connecting point shown below If the arm is not easy to press, you can rotate the arm at a 45° angle then press downward.

 

 

10. How do I know if your Monitor Mount is Compatible with my monitor?

A. Check the weight of your monitor and see if it is below the max rated load of the mount you are looking at. 
B. Check the size of your monitor and confirm if it is in the size range of the mount.
C. Check the VESA pattern of your monitor and confirm if it is 75x75mm/100x100mm if yes it should fit. 
D. If you have no VESA hole pattern on your monitor you will need a EGMUA4 Non VESA adaptor kit.

What if my monitors bolt pattern is wider then your 100x100mm VESA pattern?
You will need an adaptor plate to install the monitor to the mounts or stands.

 

 

11. Can this monitor stand be mounted on a MDF/particle board desktop?

Yes. However, the particle board is softer than a solid wood or MDF desk top. We suggest you purchase a reinforcing plate (HNDA1) for installation.

 

 ,

12. Can this monitor stand be mounted on a glass table?

Yes. But in order to protect the glass table,we suggest you should purchase a reinforcing plate (HNDA1) for installation.

 

13. There is a crossbar under the edge of my desk, How can I install the mount?

There are two methods for installation.
a.Please place a wooden block with the same size of the crossbar under your desk.
b.Or you can also use grommet mounting method to install the stand.

 

 

14. Is there any way to make the monitor stand a little higher?

If you have a thin table

you could try to place a wooden block between the tabletop and the c-clamp, which will add a few inches of height.

 

 

15. What should I do if the part that connects the monitor to the stand is skewed?

Our monitor mounts & stands come with a 360°rotation function on the head. If the head is skewed please mount the monitor first and then directly rotate it back to the right angle.
(BTW, If the mount is not attached to a desktop, it will be difficult to rotate the VESA plate by hand).

 

 

16. The vesa plate is too big/wide. How to install it if the monitor has a round on the back or vesa size is only 75x75mm?

We recommend that you use spacers and long screws M4x30mm to install.
First, fix the spacers inside/outside the mounting hole , then attach the VESA plate, and finally fix it with M4x30mm screws.

 

 

17. What should I do if the tension adjustment screw is blocked by the arm?

a. Mount your monitor to the mount or stand first, the arm needs weight to form some gravity, press down to open the adjustment points. Continue to apply pressure to the arm gradually and the arm should go down to a horizontal angle in order to access the gas spring adjust bolt.b. If you find it difficult to press the arm into the horizontal position, you could try making an angle between the two arms and try it again, this may help.

 

 

18. Why the arm cannot be fixed and would slide down?

Please check the direction of screwing, because the connecting ring has threads on one side and no threads on the other side, the screws need to be screwed from left to right.

 

 

19. What should I do if the left and right monitors cannot be aligned?

There are fine-tuning screws above the headers that attach to the VESA board, adjust the fine-tuning screws on one side a few inches to align left and right.

 

 

20. Gas spring arm cannot be held in place and lowered.

If you want to move the monitor downwards, please use a large allen key and turn it clockwise ("-" direction) continuously to reduce the tension on your arm until the monitor can hold itself at the desired height.
If your monitor is very light, several turns of the hexagonal spanner are required. One turn ≈ 1lbs

 

 

21. Gas spring arm cannot be held in place, sags and cannot be lifted.

Start by holding the arm in a horizontal position and, depending on the weight of your monitor, use a large Allen key to turn the bolt continuously counter-clockwise ("+" direction) to increase the tension on the arm until the monitor is able to hold itself at the desired height. One turn ≈ 1lbs

 

 

22. Gas spring arm is swaying from side to side.

Please tighten the screw(s) in joints.

 

 

23. IWhat should I do if the arm drifts and cannot be fixed in one position after mounting the stand?

1. First make sure that the set screws are tightened at all joints.
2. Secondly, if the set screw still drifts after tightening, we recommend that you dismantle the arm and check whether the set screw is stuck in the seam of the sleeve.
If so, turn the plastic sleeve to prevent the set screw from getting stuck in the seam.
3. If you have tried steps 1 and 2,but the problem persists.
Please take the set screw apart and see if it is shorter than the other set screws.
If so, you could replace the set screw with an M6x15mm screw and tighten it again to solve the problem.

 

 

24. Can the monitor wall mount be installed on plasterboard/drywall?

Sorry, it cannot be mounted on plasterboard walls or drywall, our monitor wall mounts can only be mounted on single wooden posts, concrete and brick walls.

 

 

25. Can the wall mount be mounted on a metal post?

Sorry, it is unable to mount on a metal post. The metal posts do not provide sufficient grip to securely mount the wall mount and may cause it to fall off.